Midtown Indigo Shaker

Width 36" | Height 34.5" | Depth 24"

2 drawer base cabinet. Each drawer front measures 14-5/8" high.

Width 36" | Height 12" | Depth .75"

Arched recessed panel valance that can be trimmed up to 3" on each side.

Width 36" | Height 5.5" | Depth .75"

Arched valance. The width of the flat section on either side of the arch is 6" and it can be trimmed up to 3" on each side.

Width 36" | Height 30" | Depth 21"

Arched wood hood with an overall depth of 21", the depth of the main part of the hood (which goes against the wall) is 15". The top panel will lift up and the sides will be flush. If crown is being installed, it would be installed above the cabinet, not on the face frame. A full interior stainless steel hood liner will also be installed (liner can be removed on site, if needed, however a hood liner is strongly recommended to prevent the wood hood from getting burned and is required by code in many places. The interior hood liner dimensions are as follows:

• Rear width: 34-1/2”
• Front width: 29-7/8”
• Depth of 34-1/2” section: 13-3/4”
• Depth of 29-7/8” section: 4-1/2”
• Max fan size: 34-1/2” x 13-3/4”
• Note that a blower is not included and must be purchased separately

Width 36" | Height 34.5" | Depth 24"

2 door base cabinet with 1 three quarter depth adjustable shelf and 2 drawers.

Width 36" | Height 34.5" | Depth 24"

Diagonal corner sink base that will take up 36" of wall space from the corner out, on each wall. The door width is 14-1/2" and the face frame width is 17". Front to back depth is 36". This cabinet will have a partial overlay door to ensure it opens without hitting the adjacent cabinet, so there will be about 1-1/8" of face frame, visible on either side of the door.

Width 36" | Height 34.5" | Depth "

Diagonal corner sink front that will take up 36" of wall space from the corner out, on each wall, once installed. The door width is 14-1/2" and the face frame width is 17". This cabinet will have a partial overlay door to ensure it opens without hitting the adjacent cabinet, so there will be about 1-1/8" of face frame, visible on either side of the door. The corner sink front floor must be ordered separately (SKU DSFL36).

Width 36" | Height 34.5" | Depth 24"

3 drawer base cabinet. Top drawer front is 6-3/4" high, middle and bottom drawer fronts are 11-1/4" high.

Width 36" | Height 34.5" | Depth 24"

Easy reach corner cabinet that will take up 36" from the corner out, on each wall. Center shelf is adjustable and soft close hinging isn't available with this cabinet. Once assembled, the door cannot be reversed, so be sure to specify left or right hinging (as if facing the cabinet).

Width 36" | Height 34.5" | Depth 24"

Farm sink base cabinet. Door heights are 17-1/2". Typically, the farm sink base should be a minimum of 3" wider than the farm sink (for example, a 30" farm sink would need a 33" farm sink base). The front panel will need to be cut on site to fit the sink and can be cut to accommodate a sink that's a maximum of 12" high

Width 36" | Height 2.5" | Depth 10"

Floating shelf that will include the mounting brackets and hardware. The weight limit is 15 lbs/linear foot as long as the proper installation instructions are followed (instructions will be included with the shelf).

Width 36" | Height 2.5" | Depth 10"

Floating plywood shelf with a walnut finish that will include the mounting brackets and hardware. The weight limit is 15 lbs/linear foot as long as the proper installation instructions are followed (instructions will be included with the shelf).