Midtown Cloud Shaker

Width 96" | Height .75" | Depth 1.5"

Starter molding that is installed above wall and tall cabinets which acts as a cleat for a molding extension (SKU: MEX-8), to make it easier to mount moldings on top of the cabinets. The starter molding and molding extension are ideal to use when mounting crown molding all the way to the ceiling.

Width 96" | Height .75" | Depth 2.5"

Stacking molding to be used as a decorative piece between cabinets that are getting stacked one above the other. This hides the 'cabinet seam' that you would normally see without a decorative molding in between or applied over the seam.

Width 96" | Height 6" | Depth .75"

Molding extension that is used with starter molding (SKU: STRM-8) to make it easier to install molding on the tops of cabinets. The molding extension can be used without the starter molding, but it would first need a cleat support installed on site.

Width 96"

Large cove crown molding. When installed, it will be 4-1/2" high and will stick out from the cabinet 4-1/2".

Width 96"

Extra large cove crown molding. When installed, it will be 5-1/2" high and will stick out from the cabinet 5-1/2".

Width 96" | Height 6" | Depth .75"

Shiplap interlocking molding commonly used for walls, backsplash, or the backs of islands and peninsulas.

Width 36" | Height 12" | Depth .75"

Arched recessed panel valance that can be trimmed up to 3" on each side.

Width 36" | Height 5.5" | Depth .75"

Arched valance. The width of the flat section on either side of the arch is 6" and it can be trimmed up to 3" on each side.

Width 36" | Height 30" | Depth 21"

Arched wood hood with an overall depth of 21". The depth of the main part of the hood (which goes against the wall) is 15". The top panel will lift up and the sides will be flush. If crown is being installed, it would be installed above the cabinet, not on the face frame.

A standard interior stainless steel hood liner is included. An upgraded liner has been removed, and pricing has been updated accordingly. The liner can be removed on site if needed; however, a hood liner is strongly recommended to prevent the wood hood from getting burned and is required by code in many locations. The interior hood liner dimensions are as follows:

• Rear width: 34-1/2"
• Front width: 29-7/8"
• Depth of 34-1/2" section: 13-3/4"
• Depth of 29-7/8" section: 4-1/2"
• Max fan size: 34-1/2" x 13-3/4"
• Note that a blower is not included and must be purchased separately

Width 36" | Height 34.5" | Depth "

Diagonal corner sink front that will take up 36" of wall space from the corner out, on each wall, once installed. The door width is 14-1/2" and the face frame width is 17". This cabinet will have a partial overlay door to ensure it opens without hitting the adjacent cabinet, so there will be about 1-1/8" of face frame, visible on either side of the door. The corner sink front floor must be ordered separately (SKU DSFL36).

Width 36" | Height 2.5" | Depth 10"

Floating shelf that will include the mounting brackets and hardware. The weight limit is 15 lbs/linear foot as long as the proper installation instructions are followed (instructions will be included with the shelf).

Width 36" | Height 34.5" | Depth 24"

Full height door diagonal corner sink base that will take up 36" of wall space from the corner out, on each wall. The door width is 14-1/2" and the face frame width is 17". Front to back depth is 36". This cabinet will have a partial overlay door to ensure it opens without hitting the adjacent cabinet, so there will be about 1-1/8" of face frame, visible on either side of the door.