Tuscan Cloud

Width 96"

Extra large cove crown molding. When installed, it will be 5-1/2" high and will stick out from the cabinet 5-1/2".

Width 96"

Large cove crown molding. When installed, it will be 4-1/2" high and will stick out from the cabinet 4-1/2".

Width 96" | Height 6" | Depth .75"

Molding extension that is used with starter molding (SKU: STRM-8) to make it easier to install molding on the tops of cabinets. The molding extension can be used without the starter molding, but it would first need a cleat support installed on site.

Width 96" | Height 6" | Depth .75"

Shiplap interlocking molding commonly used for walls, backsplash, or the backs of islands and peninsulas.

Width 96" | Height .75" | Depth 2.5"

Stacking molding to be used as a decorative piece between cabinets that are getting stacked one above the other. This hides the 'cabinet seam' that you would normally see without a decorative molding in between or applied over the seam.

Width 96" | Height .75" | Depth 1.5"

Starter molding that is installed above wall and tall cabinets which acts as a cleat for a molding extension (SKU: MEX-8), to make it easier to mount moldings on top of the cabinets. The starter molding and molding extension are ideal to use when mounting crown molding all the way to the ceiling.

Width 42" | Height 12" | Depth .75"

Arched raised panel valance that can be trimmed up to 3" on each side.

Width 42" | Height 30" | Depth 21"

Arched wood hood with an overall depth of 21", the depth of the main part of the hood (which goes against the wall) is 15". The top panel will lift up and the sides will be flush. If crown is being installed, it would be installed above the cabinet, not on the face frame. A full interior stainless steel hood liner will also be installed (liner can be removed on site, if needed, however a hood liner is strongly recommended to prevent the wood hood from getting burned and is required by code in many places. The interior hood liner dimensions are as follows:

• Rear width: 40-1/2”
• Front width: 35-7/8”
• Depth of 34-1/2” section: 13-3/4”
• Depth of 29-7/8” section: 4-1/2”
• Max fan size: 40-1/2” x 13-3/4”
• Note that a blower is not included and must be purchased separately

Width 42" | Height 34.5" | Depth 24"

2 door base cabinet with 1 three quarter depth adjustable shelf and 2 drawers. This cabinet will have a 2-5/8" center stile.

Width 42" | Height 2.5" | Depth 10"

Floating shelf that will include the mounting brackets and hardware. The weight limit is 15 lbs/linear foot as long as the proper installation instructions are followed (instructions will be included with the shelf).

Width 42" | Height 34.5" | Depth 24"

Sink base cabinet with 2 doors and 2 false drawer fronts. This cabinet will have no shelves.

Width 42" | Height 34.5" | Depth 21"

Vanity sink and drawer base combo cabinet with (1) 17-1/2" wide door in the middle, (1) 6-3/4" high false drawer front across the top of the entire cabinet, and (2) 11-1/2" high drawers on the left and right. This cabinet will not have any shelves. This vanity has the option to add a decorative platform and feet, scroll through the cabinetry images to view the two platform styles: shaker or vera, along with the two feet styles: cove or taper. The images will be shown in white but will match the finish being ordered. The cove and taper feet include adjustable plastic leveling feet for easy adjustment on uneven surfaces. The leveling foot projects 1/16" when fully retracted to elevate the feet off the finished floor and is extendable up to 1/2". The leveling foot comes pre-attached to the decorative feet and is non-removable. The platform and feet will ship loose, to be installed on-site. *If a decorative platform and feet option is selected, the cabinet will also come with finished sides.*